Search Results for ‘300’

First off here is video of issue. So I bought a 2001 300 2x4 and have been loosing my mind over this issue for 2 weeks now. Compression tested and had 139 psi. Replaced fuel filter and fuel line. Cleaned and rebuilt carb twice looking at everything to make sure it looked good. Has stock sized...

Hey i have a 91 bayou 300 and i have stater cover off and took the starter idle limiter out and noticed it doesnt not spin freely one way. I think it could possible be stuck or something, or how much force does it require to spin one way. Any help would be great thanks!

Hi. I recently purchased a 1996 Kawasaki Lakota 300. It has some issues with the clutch slipping so I decided to replace the friction plates. After I did that it was even worse than before. Acts like the clutch won't release. I ended up replacing the adjuster screw and also the centrifugal...

I have a 2016 brute force 300 that the wife rides. Ran fine in January and then my son got hurt then covid and the bike sat till about 3 weeks ago. Starts right up and idles fine. Once you start to give it gas about a quarter throttle it bogs down and dies. I've cleaned carb, ordered a rebuild...

My 01 prarie won’t operate at full throttle, you and crack it down or ease into it, as long as you don’t it full throttle, it will sputter down then cruise at about 20. It can’t be the carb, I just bought and put the new one in yesterday, and the old carb had the same problem but worse. It’s...

I picked up a Brute 300 this weekend, and it needs a few things. I'm looking for a parking brake cable, hubcap, and spark arrestor and hardware. If it has a part number in the pic, I need it. If you're parting out a 300 or simply throwing away some stuff, please let me know. You can either...

Looking for a little info on swapping a 300ex carb in place of the stocker, I have searched and found that it can be done but will need the Honda throttle cable/thumb throttle etc. My question is are there any other modifications required? thanks for any info!

Would it bolt up if not how much fab work would be involved I have a prairie frame in really good condition and a bayou engine that run with wiring harness and all electronics

Hello, I have a question of where the rev limiter is located on a Brute Force 300. I would like to take it off and replace it with an adjustable rev limiter. Is there an adjustable rev limiter? I wanted it to be taken off becuase my ATV only exceeds to 48 mph, with me and another person on it...

i was wondering if any one could explain to me the process of replacing the electric starter? I had to replace mine recently and when I went to put the starter back on I feel like the spindle in the end of the starter isn't goig all the way into the little gear with the chain on the inside. Any...

I have no experience with atv mechanics at all but last week I decided to try my luck fixing my dads 4wheeler, a 2001 KVF300 automatic 4x4. I started by draining all the old fuel out of it, cleaning the carburetor, and changing the oil and oil filter. I also put a new battery in it. I've never...

Just bought an 88 300 bayou that sat for 2 years, i cleaned the gas tank, rebuilt the carb, built a new exhaust and muffler, cleaned every electrical connection, checked the timing, new plug wire and proper plug, charged the existing battery after topping it off with water. when charged the bike...

Hey all, Here's my nightmare.......bought this quad knowing it had no spark. In the past month I've replace the wire harness, regulator, stator, and pick up coil but still don't have spark. My next piece is going to be the cdi box. If that doesn't fix the problem can anyone thnk of anything...

Is it possible to swap a 400 4x4 rear differential for 300 4x4 on a 1995. Bought a pair of 1995 bayou 400 4x4. One is complete, runs and plan on flipping it. It also came with a "parts" atv that is practically complete minus the rear differential. Seems to be difficult to find a complete...

Hi, I'm new to the Forum, and Kawasaki ATV's. I just picked up a 1999 Prairie that has bad Diff bearings in it. The problem I'm having is I don't know what MODEL this ATV is?? I'v been told it's a 2x4 300, and 2x4 360, all I do know 90% is that it is a 1999. Where can I decode the VIN to get...

i just got a 95 bayou 300 i changed the spark plugs cleaned the carb jumped it to get it runing its was running fine but when i push on the gas it dies and when i take the jumper cables off it dies but when i try to pull start it the lights will light up like the N light but it will not start i...

Hi all Desperate for a crankshaft and con-rod complete for a KLF300 c 4x4 2001 model with the con rod attached. Any rescuers out there?!

Couldn't find any good videos of the Lakota running. Mine is a 2000 Lakota 300. The camera was attached to the front of the quad but it fell off. Didn't want to waste my trip so I picked it up and kept recording. At some points it gets very shaky. That's when I tried setting the camera on the...

kawasaki brute force 300 new video My 14 years old son filmed and edited this clip over Yamaha's Grizzly score :D

I recently got a Kawasaki Lakota 300, but I cannot tell what year it is. on the frame it says KEF300A. It doesnt say A1,A2,A3 etc... :confused: is there somewhere else i can look to tell? Thanks in advance for any help.