Search Results for ‘360’

Hey guys, Got a question been searching for weeks can’t find anything on this. I got a 2004Prairie 360 4x4 the plain bearing in the left side crankcase seizes to the crank bearing was able to save the crank every measures out within specs. But having problems finding the plain bearing does...

Newbie question. The wire harness has broken wires right next to the 4 wheel drive actuator plug. A branch must have cut them. Is it possible to replace just the wire harness? Or do I have to buy a new actuator? Splicing will not work; wires too short. Thanks, rosco

2005 Prairie 360. Ran bikes with a friend last night, everything ran perfectly. My friend forgot to shut of the headlights and the light bar when he shut down. This morning, when I turned on the key, all the lights came on, including the 126 W light bar plugged into the cigarette lighter. So...

Hi.i have a 2008 kawasaki prairie 360 4x4 and I just got it on a trade. It runs fine at idle but when it gets up to about 10 mph give or take it starts to spit and sputter like your in reverse without pushing the override button. But it don't matter weather your in neutral, reverse, high, or low...

Hello Kawieriders.com: If anyone is interested, we have the true plug-n-play H.I.D. lighting upgrades IN STOCK for the stock headlamps [Kawasaki Prairie 360 2003-2013] and we need a few end-users to test them out for us. I am offering three kits at a very special discounted price if anyone...

Hi, I'm new to the Forum, and Kawasaki ATV's. I just picked up a 1999 Prairie that has bad Diff bearings in it. The problem I'm having is I don't know what MODEL this ATV is?? I'v been told it's a 2x4 300, and 2x4 360, all I do know 90% is that it is a 1999. Where can I decode the VIN to get...

i bought an 06 360 a little over a year ago. I had my fun with it and took it through hell and back. On one particular hell trip, i popped the lower ball joint out on what im pretty sure is the A arm on the left front wheel. I through a ratchet strap on it and limped it to the truck. Once I got...

Was having problems with backfire thru carbs, missing etc, so opened up machine (03 Prairie 4x4); rebilt carb; reset valves (which were both tight). Fired up machine before reassembling everything. Choke works perfectly, idle is right on the money and it revs up great (in neutral). Put it...

Hi, I wanted to to know that a 05 prairie 700 can use a 04 prairie 360 ignition key switch? Because Im looking to buy a ingnition and one that is in my price range is a prairie 360?

Hi to everybody. I've recently purchased 360 prairie 03 and I was looking for some information about the ATV. This is a great site with lot of advice and instructions. Great job! However, i still have a few problems with my prairie. The belt needs replacing cos it's completely worn with a...

Hey guys I'm new to KR and thought I'd ask some advice ... just through some outlaw mst's under my prairie 360 and it turns them good but it don't have the power to clean out when I'm in thick mud .. my question is what would be my best options for pulling some extra balls out of it ??

Can fit 26x12x12 tires on the stock rear wheels of a prairie 360 that comes with 25x10x12 tires. Also if i add a 2 in. lift could i put 27x10x12 0r 27x12x12 silverbacks on the rear? Thanks!

Hi, I recently bought a stock prairie 360 with a winch and for Christmas an audiopipe. If anyone owns or knows about prairie's what are some suggestions for modifications. Just wonderin were to start modifying it. It's practically brand new so I dont want to mess it up. I'm 13 and would love to...

Like some, i went through every post in this forum for the problem with the Belt/4x4 light and tried them all...even put in a new harness and still have the belt light and 4x4 light blinking when i turn the key on. Resets have been done (lost count) with the black and gray plug with the 2 pin...

hi everyone im new to the forum. i just bought a 2003 prairie 360 4x4. its starting to smoke and friend told me it needs a new top end anyway does anybody know where i can get a big bore kit or some way i can get more displacement out of it for more power or any other mods like cams valves...

Can anyone tell me what the vent tube is for on 4wheel actuator? 03 Prairie and many other kaw models :confused::confused:....

Ok so ive replaced the belt and reset the flashy lights. I flip the switch and nothin happens. I have checked all the fuses. What else should i look or listen for?:confused:

Hey I am new to 4 wheeling. Just bought a 03 prairie 360. I bought as is with fixing up hopes. Well rebuilt the carb and got her running. Could someone pkease tell me how to shift into gear without grindin the heck out of it? Also brake pedal is frozen up? any suggestions on freein it up...

Ok I put a HMF pipe, a jet kit with a 160 main which was the biggest that came with the kit. "155" is the stock main. Changed the needle to the Dyno jet needle set it where it said to put it. Etc etc. I have a K&N with a pre filter. I just put the silencer in the HMF as well, but this did...

Hey guys im in need of a prairie 360 ignition switch. if anyone has one please let me know. it must have the key and be working. thanks