Search Results for ‘belt’

I have a new squealing issue that appears to occur when the alternator is under load (all lights on) and the engine is revved up such as when driving. There is no noticeable squeal at idle or when revved up under no alternator load (all lights off). My suspicion is that the belt is slipping or...

I recently bought a 2003 Prairie 650. She has never been abused, as a matter of fact she had less than 150 hrs and 300 miles when I got her not even a scratch on the plastic. Rebuilt the carbs, changed the oil and filter, clean the fuel tank out and replaced the fuel pump. She rips pretty...

I put a new EPI clutch kit on my Pro fxt the other day, and now the belt indicator light comes on when it is gassed in high range. Does anyone know a way around the belt indicator light? Thanks in advance!

Total Noob when it comes to working on bikes. :| 2000 Praire 400 2x4 I rode it hard in the rain and noticed a slight knocking noise, usually when slowing down. The next day my friend rode it for an hour before stopping to let me know the the noise was worse. It didn't seem to affect the...

I just put a new belt in my 2005 BF 750. I did the upgrade to a Teryx belt and it fits fine. Here's the question. OK, I've heard about breaking in new machines. 10 hours of various throttle and speed but not wide open. But is that for the belt or the engine or everything? What do you guys...

Just picked up my baby already took her mudding...anyway I hear it's good to keep a backup drive belt and read the oem belt is probably the best to stick with..the only "oem" belt I found on ebay was made my Chaplin. Is this really the oem belt and/or which belt have you had the best experience...

My name is mark I drive a 2011 bruteforce 650 4x4i I smoked the belt bad yesterday I was going over an obstacle and wasnt in low my brand new belt had around 10 hours on it now it doesnt grab I can only go about 15 I know I have to replace it but should I deglaze or what should I look at or see...

I havent checked my CVT belt in the last 200hrs so im thinking a replacement is needed. Its not def but if it is showing signs of wear which belt brand is best? Any input on this subject would be greatly appreciated

I drove my brute force 650 sra through some deep mud holes and after the last one I heard a lot of noise coming from the belt area. I thought it was the belt shredding apart but after I took off the drive belt cover, everything looked fine. However, a horrible noise is still coming from that...

i just recently purchased a 2005 brute force 750, and i have a few problems with it. when i first rode it the 4wd 2wd lights were switching back and forth, and after a few minutes it stayed on 2wd and wont switch to 4wd. the seal around the switch for 4wd is cracked and not sealed. also, its...

hey, whats up? i am NOT mechanically inclined in any way, so bear with me. I have a 2007 Brute Force 750, and i have been having problems with it when accelerating. it seems that a majority of the time when i start to push the throttle, the machine acts like it is bogging down and instead of...

Hey guys I need to get some rear hubs and possibly a new belt. I know everyone says to get the oem over the Carlisle and the dayco but what about the epi? How does it hold up? About the hubs. Any guidance on those I've heard that oem strip easy as mine are stripped out and I've heard to go...

Like some, i went through every post in this forum for the problem with the Belt/4x4 light and tried them all...even put in a new harness and still have the belt light and 4x4 light blinking when i turn the key on. Resets have been done (lost count) with the black and gray plug with the 2 pin...

got a 2000 prairie 400, that will only run about 10 mph in hi or low. the motor is running great and seams like it wont come out of first gear, also i have to hit the gas a couple of times before it will start to move. i pulled the belt cover off to see if the belt was slipping and its not. so...

I just bought a 2003 prairie 650 4x4 that has 1300 miles on It. It is in decent shape, so far as I can tell it runs great, except for one thing. Whenever you take off from a complete stop, in high, low or reverse, the belt makes a squeaking noise. If You are moving even a little and accelerate...

Ok so ive replaced the belt and reset the flashy lights. I flip the switch and nothin happens. I have checked all the fuses. What else should i look or listen for?:confused:

If i put 28" Vampire EDL's on my 08 brute with factory clutch springs and drive it easy just for hunting will i have any problems with my belt? I had someone tell me that EDL's are not for brutes because they are belt burners. Does anyone have EDL's on their brute? Any info will be appreciated.

I am new to this so please bear with me, i am having some problems with my grandfather's prairie300, the rpm's have to be really high for it to get going, once going it has to go pretty fast to run smoothly, any ideas to what this could be? I am used to my 650 pririe, this thing seems like it is...

The other day i was running down the highway at about 60mph and all of a sudden (SNAP) my belt broke. I just bout the thing and have only rode it 5 times. I took it to the dealer and they said the guy before me may have put it under to much stress and wore the belt down. It only has 50 hrs and...